The Wyze Camera flashing blue light indicates that the camera is trying to connect to Wi-Fi. This can happen when you first set up your camera, or if there's a disruption in the connection. To fix it, make sure your router is on and broadcasting a network signal, then reset your Wyze Camera by pressing and holding its setup button for 10 ...I’m going to try this with the “bricked” one and see if it revives it. I did try to downgrade the firmware via the SD card. But to no avail it seemed as if it would work but it went back to the flashing. I’m hoping the experiment will do something and at least be a fix for those who now can’t get a base station.In the app, I removed the base as a device and then tried to re-add the Wyze base: Add device; Select Cameras; Select Wyze Base Station; Plug in the power and network cable to the base, blue light on base is flashing; app is searching for the base but never finds it; After 2 minutes, I check the box for 'The status light is solid blue', nextThe reset procedure doesn't work, the camera keeps going into"ready to connect" mode. When I plug it in, the light starts solid fed then changes to red/blue flashing after a few seconds. I am using a formatted 32 gig sdhc from Wyze. I'm going to try again, and hope for a better outcome.Troubleshooting Steps. If you’ve been experiencing your Wyze Cam v3 flashing red and blue, don’t worry – there are a few steps you can take to troubleshoot the issue. Firstly, make sure that the firmware is up to date by going to the Device Info section in the Wyze app. If the firmware is up to date, try power cycling the camera by ...I have six WYZE cameras: Three v3, and Three WYZE Cam Pans. When someone, with whom I’ve shared viewing, is watching on my V3 cameras, the status light turns solid red, and returns to solid blue when they stop viewing. This does not occur on the Pan Cams. This is an FYI of my experience with the cameras. I also have five NEST …Power cycled camera through Wyze app. Cam is stuck at blue … I too just checked back and attempted to re set up. Everything worked just fine! Thanks Wyze!! Wyze Forum Wyze Pan Cam v2 stuck at blinking blue light. Cameras. cam-pan-v2. savoy07 October 6, 2021, 3:57am 29. I too just checked back and attempted to re set up . …It was just showing a solid yellow light. I contacted the online support. It suggested I download the software from Wyze.com to see if it will get the camera working. All it did was give me a continual flashing light blue light. they say it is a router connection issue.Tried factory resetting the camera multiple times and connecting it to wifi about 100 time and get the same result. Shows as everything went ok on the app and lets me name the device but the camera eventually says connection timed out please rescan QR code, and eventually changes from blinking blue to red again. UpdateI received the V2 unit today and set it up on my home network. I upgraded the firmware and the cam worked fine for about 6 hours, until I unplugged the unit to reposition the camera and add the extension cable. I proceeded to plug the cable back into the camera and nothing…just a solid yellow light. I unplugged and plugged back in…the …All of my Wyze cams have a blinking blue LED this morning. They are all working ok…just the blinking blue LED. My wifi network is fine. I’ve tried a power cycle…didn’t help. Very strange.Troubleshooting Steps. If you’ve been experiencing your Wyze Cam v3 flashing red and blue, don’t worry – there are a few steps you can take to troubleshoot the issue. Firstly, make sure that the firmware is up to date by going to the Device Info section in the Wyze app. If the firmware is up to date, try power cycling the camera by ...Note: The "Solid Blue" in this case is not the same as the one normally seen on the camera. Instead, both the blue and yellow LEDs will be on at once, making it appear to be a lighter blue.* This is what I was referring to as the blinking light blue light. Problem is it continues to blink - never turns blinking yellow or solid "dark" blue.insert sd card in V2 (unplugged) with finger on reset button. plug in power for around 3-6 sec. should see light blue led light. (actually both blue and yellow are both on. wait until led turn to yellow. remove sd card. restart v2. once flashing yellow started. press reset button. it will announce ready to connect.Fixing Wyze Base Station Flashing Blue. Change Ethernet Cable. If your base station is in perfect shape, then the first thing you should do is change the ethernet cable. Several owners have pointed out that the issue with the base station flashing is mostly related to a defective ethernet cable.The updated firmware made it worse, as I stated in my earlier post. The camera stays connected for less than 60 seconds since flashing the latest firmware. This HAS to be a hardware issue with the new firmware. I have 2 v2 cameras that are fine, and 2 v2 cameras that have this issue of not being able to stay connected.Blinking blue LED on all cams (v1 and v2) - Cameras - Wyze Forum. Cameras. mikewilsontx November 19, 2018, 2:31pm 1. All of my Wyze cams have a blinking blue …The status LEDs will turn from solid yellow to flashing yellow and blue. Note : You must remove the battery cover to access the setup button. For Wyze Cam Floodlight & Floodlight ProHi, I bought my Wyze Cam V2 about 6 months ago. I mainly used it to watch my puppy while I am at work, and worked great! Few days ago, I got into trouble connecting my cam through phone. Do not remember exactly what it was saying, but it kept trying to attempt connecting to network. Also, light at the back was flashing between yellow and blue. Did look through few threads here, and tried the ...In this blog, we'll explore what causes the flashing blue light on your Wyze Plug, the steps to take to troubleshoot the issue, and how to prevent it from happening again. Think of it as a roadmap to help guide you through the troubleshooting process and get your smart home back to working properly. So, grab your Wyze Plug and let's get ...To fix this issue, try resetting your Wi-Fi router and re-connecting your Wyze cam to your network. Another reason why your Wyze cam may be saying offline is that the camera may need a firmware update. To check if this is the case, go to the Wyze app and check for any available updates.Check Camera Connectivity. If you’re experiencing an issue with your Wyze Cam v3 flashing red and blue, it could be due to an issue with camera connectivity. The first step in troubleshooting this issue is to check …A month ago, I saw that my Cam Pan V2 was flashing red and blue lights and per Wyze rep instructions, I flashed the firmware and it seemed to have worked. However, today, I noticed that the same thing is happening. To be clear, when it is sitting still, it shows blue light but when it turns, then it turns red and after sitting still, it turns …This is happening to me with RTSP firmware which is stagnant but after app update 2.48.5 and only with Pan V2. The rtsp url works just fine from any viewer, but the moment I try to use the Wyze app the blue light starts blinking and refuses to display the feed within the Wyze app. Says it is offline which is not the case as they shows up on my router's client list.Netflix released its July slate of mobile games yesterday, adding a range of new titles. One game, in particular, called Before Your Eyes, uses eye-tracking technology that progres...Wyze Cam will continue to flash yellow and blue at the same time if the webcam firmware is installed properly and the camera is turned on. To use your new webcam: Connect the USB A to A cable to the Wyze Cam USB port and the computer USB port. In your video conference tool (ex. Zoom), change the camera source to "HD USB Camera."Step 5: Complete the setup on your Wyze app. Open the application on your smartphone. Press the Add Device (+) button on the upper left side of your screen. Under Power & Lighting, tap Wyze Plug. Choose Next. Wait for your Wyze plug to finish connecting with the app via Bluetooth.Did a camera firmware update and it worked for the weekend. Then I checked and it was offline. Basestation was flashing blue. I disconnected it and reconnected same thing. Connected it to my router directly and powered it back on and same thing. Flashing blue. All other Wyze devices work fine. Just base station is showing flashing blue…Reset the Device. If you see your Wyze camera’s blue light blinking, it may indicate that there is a problem connection between your device and Wi-Fi network. The first thing you should try is to reset your device. To do this, simply press and hold the setup button for about 10 seconds until you hear a voice prompt saying “Ready to connect.I received the V2 unit today and set it up on my home network. I upgraded the firmware and the cam worked fine for about 6 hours, until I unplugged the unit to reposition the camera and add the extension cable. I proceeded to plug the cable back into the camera and nothing…just a solid yellow light. I unplugged and plugged back in…the …A working V2, when reboot or power cycled, will get stuck flashing yellow/blue. Y/B flashing indicates a problem connecting to WIFI. ... I had the same problem when upgrading both of my Wyze Cam v2 to firmware version 4.9.9.172: initial setup works until reboot, then camera gets stuck flashing the yellow and blue LEDs forever after a reboot. I ...Long shot, but try first 1) hard restarting your device, 2) deleting your app and reinstalling it, and/or, 3 )if you have a second device, try installing using it. This is really reaching, but…. 2 Likes. tombsc September 2, 2020, 6:50am 10. Tried all of the above, and finally reflashed the firmware as suggested.If you ever notice that the blue light on your Wyze Camera is continuously blinking, this indicates that there is a connectivity issue or that the camera has lost connection to the internet. Overall, understanding the blue light on your Wyze Camera will help you troubleshoot any issues that may arise and ensure that your camera is working ...The last link that was sent to me was for installing firmware for use of the Wyze Cam v2 as a web cam. I do not want to use it as a web cam. I also made sure to use the power adapter that came with it, 5V, 1A power adapter. The light turns on yellow and starts blinking slowly while the camera clicks. To clarify, this is a Wyze Cam v2, Model WYZEC2.The flashing blue light on your Wyze device can be frustrating and confusing, but fear not, we've got you covered. In this troubleshooting guide , we'll walk you through common reasons why your Wyze device might be constantly flashing blue and what steps you can take to resolve the issue.Dec 6, 2023 · A solid blue light on Wyze Cam v3 usually indicates that the device has properly been set up. If you get a solid blue light yet the setup has failed, try following these troubleshooting steps: Force close the app, reload it, then retry the connection. If that doesn't help, power cycle the camera.Note: The "Solid Blue" in this case is not the same as the one normally seen on the camera. Instead, both the blue and yellow LEDs will be on at once, making it appear to be a lighter blue.* This is what I was referring to as the blinking light blue light. Problem is it continues to blink - never turns blinking yellow or solid "dark" blue.During Installation and Setup. Solid red light - The camera is powered and starting up. Flashing red light - Ready to connect to Wi-Fi. Flashing red and blue lights - Connection is in progress. Flashing blue light - The camera is connected and finishing setup. Solid blue light - Camera is powered, connected, and working properly.After the router is connected to power and has booted up: Flashing white light - In pairing mode. Flashing blue light - BluetoothⓇ provisioning process. Solid white light - Successfully paired or initially powering on. Flashing orange light - Router is booting up. Rapidly flashing orange light - Factory reset via pinhole method has initiated.Base Station, with wireless connection, and 3 Outdoor Cams all with latest firmware updates as of 8-15-21. Worked great for several months. Now the base and all 3 cams are offline. Light on base is flashing blue. Power cycled the base and on restart got steady yellow then flashing blue light. Wired (ethernet) base to my router, same results. Removed base from app (latest version) and tried to ...If the cam will not log into the network, will not enter a new setup routine, or will not factory reset, a firmware flash is the last resort. Download the firmware, transfer to a blank 32GB card, unplug cam, insert card, press and hold setup button while plugging it back in and wait for the red\blue=purple lights. Wyze.Turned on cam today and wasn't able to connect to camera. Power cycled camera through Wyze app. Cam is stuck at blue … Thank you @golemj and welcome to the community as well! Are you seeing this with more than one Cam Pan V2? Wyze Forum Wyze Pan Cam v2 stuck at blinking blue light. Cameras. cam-pan-v2. R.Good October 5, 2021, 3:20pm ...Cameras. mycle September 24, 2021, 9:36pm 67. Here's what worked for me: Try switching the base station to a different port on your router. As long as it was different from the current port it worked for me, even after I went back to the original port. I'm on a Google mesh network and it had been working fine until I loaned the base to ...I thought this was a one off, but its happened multiple times now, to different cameras at different locations i have. i accept a $20 dollar camera/bridge setup will need an occational reboot due to unhandled software issues, but Wyze intentionally decided to indicate bridge offline with continuous orange/blue flashing lights that needs a ...Factory reset Wyze Cam Floodlight v2. Remove any microSD card inserted into the floodlight. With the floodlight powered on, press and hold the setup button on the side of the camera for 10 seconds until the status light on the front of the camera turns solid red. Once the status light starts flashing red, set up the floodlight like new.In the Wyze app, tap on your Wyze Plug. Tap the settings icon > Wyze Support > Submit a log. Choose Connectivity Issues. Fill out the details and submit your app log. Write down the generated app log ID just in case you have to send it in to support. If your Plug has to be regularly set back up after falling offline, please contact us so we can ...After a week of waiting for a new outdoor camera it was finally delivered yesterday. But this brand new camera comes with the same dreaded problem of the flashing blue light. I noticed the light turned blue for a few seconds, but that was not enough time to open the app and connect. We have several other indoor cameras that have been working great.Blinking blue light on mine is a condition of overheating. I've suspended the unit at a 45 degree angle with the front pointing down and the antennae on the upper end. This has kept it cool enough for about 4 weeks of operation before it requires to be unplugged and brought down to room temperature. This base station should be a little bigger ...Wyze camera not connectiong and flashing lights (LED) Red and Blue.See how to fixt the problem.Removed base station from app. Plugged into main network switch. Held reset pin for about 15 seconds until flashing blue light stops, momentarily goes solid blue, then to yellow. Unit reset, flashed blue for about 30 seconds and then went to solid blue. Setup as new base station on app. Set camera to "new" base station. Voila! Good Luck. p.s.I just get the flashing blue light and can not get past that. I even do the whole scan code thing and… I'm facing the same issue. ... Wyze Forum Base station not connecting - flashing blue light. Cameras. Lovcheapcams December 19, 2020, 11:53pm 14. I'm facing the same issue. I have tried connecting to the main router and nest Wi-Fi router ...scsi050 February 4, 2021, 6:33pm 1. When it is dark outside, the blue LED from the push button on the front of the doorbell cam is very bright. Anyone walking by can can clearly see the blue shine and I don’t care to draw attention to my doorbell camera. Personally, I would like to see the option of having the LED either turn off or change it ...Note: The "Solid Blue" in this case is not the same as the one normally seen on the camera. Instead, both the blue and yellow LEDs will be on at once, making it appear to be a lighter blue.* This is what I was referring to as the blinking light blue light. Problem is it continues to blink - never turns blinking yellow or solid "dark" blue.Plug Wyze Base Station into a different power outlet. If this helps, then the power outlet may not be powered. Try using a different Ethernet cable. If this helps, then the cable itself may be faulty. Try a soft reset. Hold down the Sync button on the base station until the status light turns solid yellow. Once the status light begins flashing ...Tap The QR code isn't scanning and manually enter the Base Station's MAC address. Tap Go to Wi-Fi selection, then select the network that looks like " Wyze_bind_xxx ". No password is required to connect to this network. We suggest you turn off your mobile data (4G, 5G, or LTE) to optimize your connection to Wi-Fi.Ensure the camera is within range. Restart the Camera & Router. Unplug Wyze camera and router for a few minutes. Plug the router back in and wait for it to fully reboot. Plug the camera back in and wait for it to connect. Sync Camera with App. Open the Wyze app and check if the camera is offline. If it is, delete the device and set it up again.Detailed Wyze Cam Floodlight v2 Status Light Guide. Status light: What does the light mean? Solid red light. The floodlight is powered on and initializing, the user is watching the live stream, or an Event is being recorded. Flashing red light. The floodlight is ready to connect to Wi-Fi. Flashing red and blue lights.I have a lot of time trying to get the base station to connect to wifi. Updated to newest firmware and also tried some of the older fimrwares. But the base station always just starts with yellow light for a while and then changes to blinking blue. The base station doesn't seem to read the sd card. I've tried one that was laying around and also a brand new card. The same happens when I try ...If it's not flashing blue and yellow, it is not in pairing mode and you won't be able to set it up. I f your Wyze Cam Outdoor v1/v2's status light isn't on at all, make sure the power switch is in the on position. Make sure Wyze Cam Outdoor v1/v2 has a strong signal for setup. Try setting up the camera within 1-2 feet of the router.Tried factory resetting the camera multiple times and connecting it to wifi about 100 time and get the same result. Shows as everything went ok on the app and lets me name the device but the camera eventually says connection timed out please rescan QR code, and eventually changes from blinking blue to red again. UpdateWyze Battery Cam Pro Status Lights. Solid yellow - The camera is powered on and initializing. Flashing yellow and blue - The camera is ready for pairing. Solid blue - The camera has been paired successfully. Solid red - The camera is connected and powered on, an Event is being recorded/uploaded, the user is viewing the live stream, or a log is ...